Conditional Formatting With < Symbol |
Conditional Formatting With < Symbol - Excel |
|
I'm using a formula in conditional formatting to highlight cells values compared to a standard i.e. greater than or equal to or less than.
Most values will be straight numbers but others will be entered with a < symbol leading the number. The formatting I'm using is simple red green (red bad green good). The problem is when I enter a value with a < symbol the cell turns red.
All help greatfully accepted. Example attached.
Thank you.
Similar Topics
The call times are in the custom format h:mm, although it could easily be changed to an Excel time format. I'm using Excel 2002. I want the cell to have a different fill color if it falls within particular time frames.
Example: If the call came in between 22:00 and 23:59 color is light green.
If the call came in between 23:59 and 08:00 the color is yellow.
Example spreadsheet is attached.
Thanks in advance.
Does anyone have any suggestions about how to maintain the formatting when people just do a traditional C&P ?
Thanks
I have entered the following formula in to a cell: =IF(S3<R3,"DOWN","UP") it works however i want to replace the word Down and up with the relevant arrows symbol. How do i do this?
Thanks
I want F3 to turn yellow if someone selects "Yes" from a drop down list in cell E3, then F3 has no fill once data is entered into it. And F3 turns Black if E3= no selected from the list. Or F3 turns red if E3 contains "TBC"
so in summary,
if E3="Yes", then F3 conditional format to Yellow until data is entered in it.
if E3="No", then F3 conditional format to Black
if E3="TBC", then E3 & F3 conditional format to Red until E3 is changed to
"Yes" or "No" at a later time.
Thanks in Advance for the help
Mutley13
it is a function of conditional formatting. I know it is possible because I
have seen it before but I do not know how to do it.
I am new to using Excel and I am not very computer literate. I am looking for some help with a spreadsheet I am making. Here is the problem:
I have a column of 14 numbers in cells A1 to A14. If all of these values are less than 2%, I would like a "Pass" to display in cell B1. If any of these values are greater than 2% I would like a "Fail" to display in cell B1.
I have got a formula that works for a single cell but I can't figure out how to get it to apply to more than one cell. For example, I have entered =IF(A1<2,"Pass","Fail") in cell B1. Now if the value I enter in A1 is less than 2, it shows a "Pass", and if the value in A1 is greater than 2 it shows a "Fail" in cell B1. How can I get this to apply to all of the cells from A1 to A14?
If somebody could help me out that would be great.
Thanks,
Randy
My question is:
Is there a way to check for duplicates, and then automatically add numbers to the duplicate values to make them unique? If so, how can this be done?
So that you will have this:
JohnSmith
JohnSmith2
JohnSmith3
JaneDoe
JaneDoe2
JohnAdams
JohnAdams2
JohnAdams3
JohnAdams4
I think I have done a good job in illustrating what I would like to be able to do, but if there is still something that is unclear, I will post whatever clarification is needed.
Thank you in advance for your help!!
My Cell C3 is a numeric value.....I have set conditional formatting to
make the text red and bold when the number is equal or less than 10,000
is there a way I can make cell E3 display a message when the C3
condition is true?? or if not a message is there a way to make a
message box pop up when my C3 condition of less then or equal to 10,000
is true?
how would I do something like this?
I am trying to make excel automatically add a leading zero to values which are 5 digits long;
i.e. number input is 15185, then excel automatically changes it to 015185.
If I put a Customer Number Format of 0##### it works, however, a user could put any length of number into these cells, and if the number is less than 5 digits I don't want a leading zero.
Is there any way of writing a small macro to sort this out.
The numbers would be input into range B16:223.
Many thanks,
Andy
When I open any spreadsheet (new or already populated) the black box that normally frames the active cell is missing (showing which cell you have selected). Likewise when I 'select all' the sheet does not become shaded.
In addition:
Can not fill series
Can not change cell format (specifically to show Currency or Accounting w/$ symbol)
And I am sure there is much more that I have not found yet. I have not seen a single thread on this topic anywhere on the internet.
Help!
How can I get the separate lines of text in my textbox to be properly displayed in a cell? Thanks for your help in advance..
Instead of the y axis being on the left hand side, i wish for it to cut at 0,0. I have positive and negative values and I need it to be in the centre instead of on the left.
I have tried formatting both the axis and it would appear that the x axis already cuts the y axis in the right posistion so i need to format the x axis to make the y axis cut it at 0,0. I have already tried typing in 0 instead of 1 and it keeps saying it need to be number more than or equal to 1.
Any help would be greatly appreciated.
Nicole
would really appreciate anyones help with this.
I have a column full of text-formatted fractions...
4/5
6/4
3/1
2/5
4/5
etc, etc.....the column is very long!!
I need to convert these to actual fractions...ones I can add to equations, allowing me to multiply and add.
If I highlight the column and goto "format Cells" and change to fraction, the values still stay in the left of the cell.....its only when I manually click on each individual cell, then tick the little green tick, does the cell validate, and the value in the cell moves to the right (and is therefore a proper value).....problem is I have to keep doing this for each individual cell.....and I have 70000+ cells in this column!
Any suggestions on how I could speed this up?
thanks
statement? What I have in mind is something like this (stated simply): If
cells B9 or N9 or Z9 or AL9 are blank, do nothing, else color text in cell S4
red.
Thanks!
I have formulas to add a number of days to a cell containing an entered date and display the resulting new date (ie. 03/01/2011 (c34)+11 = 03/12/2011)
I am seeking to leave resulting formula cell blank until a date is entered in the input cell. Currently when the input cell is empty the formula cell obviously displays 1/11/1900 using the above example.
What conditional format would achieve leaving the formula cell blank until date data in entered into the source cell?
Hopefully a simpler question for your experience level than mine.
Are there any ways around this so that it updates upon dragging the formula?
I have an array of 9 columns and 20 rows with equity symbols and conditionally formatted to show the severity of price movement in either direction.
Instead of typing in the value of whatever cell a trader is looking at I would like for them to just be able to click on the cell and have that symbol copied into R4 so some detailed information can be displayed for them.
Can't find a thing about this on any forum or msdn.
Hope I'm explaining this at least somewhat clearly.
Thanks.
A specific problem is cells which don't have borders show up with very light grey borders in Outlook. This, I do not want.
TiA