Macro That Submits Data To Hyperion

Hi there, longtime user firsttime poster. Looking for some help as I am a non-expert with macros. Here's what I'm trying to do:

We have to submit things to a certain regulatory body and we usually enter tasks in as soon as they come, do the submission, and then keep a record of that submission.

So, I have a workbook with two sheets, one is "TO DO", the other is "ARCHIVE". Both sheets have the same columns and everything. I am looking for a macro that will automatically cut a (row) from the TO DO sheet and paste it in into the ARCHIVE sheet once it is done, then delete the cut row from the TO DO list so it stays topped up.

The trigger for archiving is the columns M and N which are titled "Complete ?" and each has a validation drop down that says "YES". When both cells in columns M and N have the YES in them, I would like the macro to make the above mentioned actions.

I ran a search on the forums and found something similar, but not quite what I was looking for.

Any help?

I am looking for the code to select the visible data after applying a data filter. Actually I know how to select the data after applying the data filter but the issue is I am not able to exclude the header row and give the target range as used (non-blank) rows only!!

I am using below code to Select the Visible rows in the target range:

Code:

Range("A:p").SpecialCells(xlCellTypeVisible).Select

Problems in this code a

1) after applying the filter, while selecting the data it is selecting all the rows in given range till last row on the workbook. I need this to select the the data only till the last used row in the given range.

2) It is not possible to provide the address of the first row after we apply the filter since the first row address may change depending on the values in the table.

E.g. 1st time when I am running the macro the first row in the visible filtered data is starting at Cell address A4 and next time when I will run the macro it may be A6

3) The Code is also selecting the 1st row which is a header row. How can we exclude it from selection.

Some one please revert with the solution.
Thanks in advance.

Hey there,

I have been tasked with introducing userforms into an excel sheet and tbh I'm quite amazed that excel has this capability of adding userforms to excel sheets.

Anyway, I have 2 columns of data in an excel sheet and I wish to add this to a userform so that the userform displays the 2 columns beside each other with headings, like a table. The user should then be able to select a particular row and insert it into the specified cell.

I would also like the user to select a row on the table and then be able to bring up another table depending on the row selected...basically so that the user can draw deeper into the information that they require.

I have an example excel sheet where I have 2 sheets. One sheet is the user entry sheet called User Entry Screen. the next sheet is the tables sheet where my tables are held. Once the user selects the cell shown in the example sheet, it should then bring up the user form. the user then, depending on which item clicked, then gets shown the next window with a table and info on it. then user should then be able to select an item and the cells on the user entry screen would then get populated.

Personally I think this is a really tricky challenge and any help with doing this would be extremely appreciated.

I'll post up further comments as I am trying to work my way through it!

Thanks,

Jag

I'm trying to use VBA to go to a website that requires a User Name, Password, and a Submit Button.

So far I can get everything to work besides the Submit part. The code runs without errors, but doesn't actually "hit" the submit button on the webpage.

For posting, I removed my actual user name and password and and used the generic " User Name " and " Password " highlighted in blue.

I highlighted another section in green that I took from a previous post hoping it would solve my problem. The link is: http://www.mrexcel.com/forum/showthr...xplorer+submit


Here is the code I am using:

Sub GoToWebSiteAndPlayAroundNew()

Dim appIE As Object ' InternetExplorer.Application
Dim URL As String


Set appIE = CreateObject("InternetExplorer.Application")
URL = " https://efolio.morgankeegan.com/escripts/defaultLogon.asp?errCode=2 "


With appIE
.navigate URL
.Visible = True

Do While .busy: DoEvents: Loop
Do While .ReadyState 4: DoEvents: Loop

.document.getelementbyid("fUserName").Value = " UserName "
.document.getelementbyid("fPassword").Value = " Password "

End With


On Error Resume Next
x = 0
For Each mitem In IE.document.all
mitem.Value = "x"
x = x + 1
Next

x = 0
For Each mitem In IE.document.all
If x = "Submit" Then
mitem.Click
Exit For
End If

Next

End Sub

Hi all.

I have set up a workbook that is sent out to lots of different users. They each keep and use their own copy.

I have set it up so that everything looks OK and is visible on MY screen, but I'm conscious that some users may have different screen sizes, different toolbars set up, and so on, which might make some parts not immediately visible to them.

I have set up an auto-execute macro which automatically sets the zoom factor to best fit, for several of the worksheets, and this works fine.
Here's the code that does it.
Code:

Sheets("WELCOME").Select
    Range("A1:N18").Select
    ActiveWindow.Zoom = True

By repeating this code for each worksheet, I can make each one be zoomed just right.

However, the file contains 8 sheets that are all identically laid out, except the number of rows is different.
What I want to do is go to the worksheet that has the largest number of rows (it's always the same worksheet, so I know which one it is), set the zoom factor for THAT worksheet (which I can do, and it always has the same number of rows), and then take THAT zoom factor, whatever it is - and it will vary depending on the user - and apply that to the other worksheets that have a similar layout.

I could just go through each worksheet and zoom it automatically, but that would mean that some of the sheets looked very large, others very small, and I'd like them to have a consistent appearance.
I could also specify a range on each worksheet that was similar to the appropriate range on the longest worksheet, and zoom that automatically, but that's not ideal either, because some of the row heights vary from sheet to sheet, and again I'll end up with different font sizes.

Anyone know how to do this ?